CrossFire ® PRO
Assembly A place to discuss your experiences with assembling the CrossFire PRO CNC Plasma Machine. Visit the CrossFire PRO Assembly Guide for more information. Troubleshooting Discuss any issues and potential fixes for your machine. General Discussion General Discussion about the CrossFire PRO CNC Plasma Table. Tips and Tricks A place to discuss helpful Tips & Tricks for cutting on the CrossFire PRO.
| Topic | Replies | Views | Activity | |
|---|---|---|---|---|
|
Interference From Plasma Cutter Freezing FireControl
Since beginning the delivery of CrossFire PRO machines, our number one priority as a company has been to chase down issues and offer permanent solutions to them. This is evidenced by our frequent updates to THC firmware … |
|
159 | 14156 | March 14, 2022 |
|
FIX: IHS Triggering Before Torch Touches Plate
We have heard a few people having one or both of the following symptoms: Randomly, the torch will drive down for IHS, but never reach the plate before raising up to fire the torch. Randomly, the torch will drive down f… |
|
3 | 12557 | September 15, 2020 |
|
LS-THC Arc Voltage Troubleshooting Guide
LS-THC Comprehensive Troubleshooting Guide 6/11/2021: We have created a THC Troubleshooting Flow chart that should greatly increase your ability to fix any THC related issues. We highly recommend first working to this c… |
|
55 | 29722 | March 25, 2025 |
|
Windows 7/8 Manual Driver Installation for FireControl
If you are planning to operate your CrossFire PRO machine using a Windows 7/8 computer, we have put together instructions for how to download and manually install the required USB driver for the CrossFirePRO Motion Contr… |
|
5 | 2423 | February 14, 2023 |
|
LS-THC Firmware Update for Bug Fixes (Current Version is V1.09 on 5/1/20)
The following guide provides instructions for how to flash the current version of the LS-THC firmware onto your unit using your computer through the USB cable. If you are experiencing any of the issues that are detailed … |
|
2 | 7837 | March 23, 2020 |
| Torch Cuts off Shortly after start |
|
5 | 16 | December 23, 2025 |
| Machine showes up out side the table |
|
9 | 38 | December 21, 2025 |
| Does anyone still have this file? ...or better |
|
20 | 121 | December 20, 2025 |
| What have you done on your CrossFire Pro Today? |
|
2303 | 58366 | December 17, 2025 |
| Water Bladder - has anyone used one? |
|
3 | 95 | December 16, 2025 |
| R/W cut 45 torch and consumables selection. |
|
4 | 39 | December 15, 2025 |
| Your file storage hierarchy thought process? |
|
11 | 114 | December 11, 2025 |
| Razorweld X45 Consumables - Nozzle tip options? |
|
9 | 2235 | December 9, 2025 |
| What circuit breaker and Wiring is used? |
|
3 | 73 | December 9, 2025 |
| No mounts for a machine torch..only hand help. |
|
3 | 55 | December 8, 2025 |
| X-Axis Gantry Wobble |
|
4 | 94 | December 7, 2025 |
| Design help, tool path issues |
|
1 | 35 | December 6, 2025 |
| Crossfire pro 9pin connector |
|
4 | 31 | December 5, 2025 |
| Torch suddenly lifts and stays on |
|
1 | 31 | December 5, 2025 |
| Solving Crossfire Pro CUT60 EMI and Ground Loop issues once and for all |
|
15 | 322 | December 4, 2025 |
| Best leveling castors for table |
|
5 | 121 | December 4, 2025 |
| Hypertherm Powermax 30xp settings |
|
5 | 1450 | December 2, 2025 |
| 50 amp extension cord? |
|
3 | 83 | December 2, 2025 |
| Tool path won't register cuts or changes location of cuts - Solved |
|
2 | 68 | December 2, 2025 |
| New to forum looking for some suggestions |
|
2 | 83 | December 1, 2025 |
| Bar sink drain dimple die |
|
672 | 24068 | December 1, 2025 |
| Mounting a welding sheild to Z axis |
|
1 | 53 | November 29, 2025 |
| Z axis stepper motor replacment |
|
21 | 215 | November 26, 2025 |
| Torch Height Pierce Issue (Too High) |
|
7 | 135 | November 23, 2025 |
| Jagged cuts on some arcs but not all |
|
48 | 97 | November 23, 2025 |