|
About the Tips and Tricks category
|
|
1
|
763
|
January 8, 2021
|
|
Designed/Printed a plastic Mobo Stand-off and used nylon screws for pure isolation
|
|
1
|
42
|
February 2, 2026
|
|
Great YouTube plasma shorthttps://youtube.com/shorts/q4rusIhoyqc?si=yYtbCPZM76Nn65Vz
|
|
2
|
91
|
January 19, 2026
|
|
Speed of cuts for crossfire pro
|
|
1
|
48
|
January 5, 2026
|
|
I am new to the whole CAD and G code world and i don't know what I'm doing
|
|
3
|
115
|
November 22, 2025
|
|
Fixing torch speed
|
|
2
|
58
|
October 17, 2025
|
|
Refrigerated air dryer
|
|
3
|
127
|
October 4, 2025
|
|
Simple Laser Pointer
|
|
36
|
723
|
August 26, 2025
|
|
Autodesk fusion personal
|
|
2
|
79
|
August 24, 2025
|
|
Legs of deer are burning out
|
|
9
|
132
|
July 30, 2025
|
|
Aluminum cutting with Nitrogen
|
|
21
|
317
|
July 25, 2025
|
|
Piercing Aluminum
|
|
19
|
370
|
July 20, 2025
|
|
Prepare for powder coat
|
|
34
|
932
|
June 25, 2025
|
|
A few table upgrades
|
|
1
|
159
|
June 16, 2025
|
|
Where is the short gcode file for cut height?
|
|
24
|
195
|
June 8, 2025
|
|
My Frankenstein Crossfire
|
|
3
|
206
|
March 28, 2025
|
|
need to slow down
|
|
1
|
105
|
March 18, 2025
|
|
Water table fluid
|
|
192
|
53612
|
March 9, 2025
|
|
Remote Controller For PRO and XR
|
|
25
|
449
|
January 15, 2025
|
|
Power Strip Isolators
|
|
0
|
82
|
December 5, 2024
|
|
Tail after finishing a cut
|
|
16
|
212
|
October 16, 2024
|
|
IHS fail the torch did not reach material within programmed travel
|
|
11
|
318
|
July 11, 2024
|
|
Common reasons folks have trouble with cuts
|
|
3
|
459
|
June 12, 2024
|
|
Slat assembly and water tray Maintenance
|
|
6
|
2513
|
April 13, 2024
|
|
Plasma cutting aluminum
|
|
5
|
1640
|
January 5, 2024
|
|
Clamping down material - binder clips!
|
|
28
|
4756
|
December 5, 2023
|
|
Pictorial cut problem guide?
|
|
6
|
593
|
November 23, 2023
|
|
CrossFire Pro- Setup overview- Beginner Guide
|
|
4
|
1264
|
November 4, 2023
|
|
Do Not Laugh at Me, IR5?
|
|
16
|
695
|
November 3, 2023
|
|
New to Crossfire
|
|
5
|
564
|
September 17, 2023
|