LS-THC (Torch Height Control)
Plasma Cutter Wiring (Raw and Divided) A place to share with others how to wire your specific plasma cutter to the LS-THC VIM module for Raw or Divided Voltage input. Helpful guides will be ‘stickied’ to the top of this thread for easy access. Please refer to the Langmuir Systems LS-THC User Guide for proper installation instructions.
| Topic | Replies | Views | Activity | |
|---|---|---|---|---|
|
WIRING EARLY RAZORWELD CUT 45 Plasma Cutter (without Voltage Divider)
:point_up_2::point_up_2::point_up_2::point_up_2::point_up_2::point_up_2::point_up_2::point_up_2::point_up_2: Click above for direct route to the post. |
|
1 | 2998 | April 14, 2020 |
|
THC Hookup Hyperthem 30 Air
Hey Guys Just on the final steps of setting up my new pro, has anyone wired a THC into the Hyperthem 30 Air? Torch triggers was quite easy but I am confused to where I want to hook up the THC Wires. I am assuming Black… |
|
5 | 1552 | April 12, 2020 |
|
Hypertherm 30 xp VIM Box RAW Voltage Wiring Quick Guide Pics
Here is a quick guide pics to connect a VIM box ( Raw Voltage ) side to a Hypertherm 30 xp. |
|
18 | 4683 | February 2, 2024 |
|
THC Arc Voltage Troubleshooting Guide
Please find our comprehensive LS-THC troubleshooting guide here: https://forum.langmuirsystems.com/t/ls-thc-arc-voltage-troubleshooting-guide/8193/2 |
|
6 | 4099 | January 2, 2026 |
| About the LS-THC (Torch Height Control) category |
|
2 | 1856 | March 23, 2020 |
| wont run with thc |
|
4 | 26 | March 3, 2026 |
| LS-THC low or no voltage Issue solved.....at least for now |
|
5 | 505 | January 11, 2026 |
| Titanium 65 wiring |
|
31 | 6367 | December 6, 2025 |
| New thc and limit switch issues |
|
7 | 77 | December 1, 2025 |
| Issues with THC |
|
0 | 62 | November 20, 2025 |
| Powermax 800 raw voltage |
|
0 | 16 | November 12, 2025 |
| THC Just stays in one place |
|
10 | 91 | November 11, 2025 |
| Propoint 45A trigger pins |
|
10 | 72 | October 16, 2025 |
| Any one seen this cable |
|
7 | 119 | September 21, 2025 |
| Cutting Voltage Lost During Cut Crossfire XR |
|
11 | 166 | August 19, 2025 |
| Cut height higher than what is set |
|
13 | 254 | June 18, 2025 |
| LS-THC Problem with head staying down |
|
1 | 71 | May 13, 2025 |
| Macbook Pro power supply causes THC to stop working |
|
1 | 63 | April 21, 2025 |
| IHS THC not working properly |
|
9 | 155 | March 23, 2025 |
| Titanium Plasma 65 CPC port |
|
8 | 314 | January 22, 2025 |
| Tomahawk 625 compatability |
|
0 | 37 | January 22, 2025 |
| Razorweld 45 50:1 pins |
|
2 | 61 | January 16, 2025 |
| New razorweld 45 connections on XR |
|
1 | 138 | January 16, 2025 |
| THC rises and does not come back down in the same cut |
|
12 | 162 | December 15, 2024 |
| Lincoln Tomahawk 625 Raw Voltage Question |
|
14 | 299 | December 5, 2024 |
| IHC cable connections (SOLVED) |
|
3 | 124 | November 25, 2024 |
| Ls-thc hypertherm 45xp |
|
5 | 925 | November 7, 2024 |
| 0 volts at CNC port Razorweld 45 |
|
9 | 132 | November 1, 2024 |
| Z Axis bobbing up and down |
|
15 | 667 | October 15, 2024 |
| Trying to understand THC and IHS. New User |
|
8 | 1804 | October 15, 2024 |