Twitch (and youtube) Live Streams CAD CAM

[TinWhisperer]

Live stream making a “let it snow !” wall hanging didn t go very smoothly but got it done in the end.

FireShare offering

https://www.langmuirsystems.com/fireshare/xmas-2022-let-it-snow-hanging-lf-tinwhisperer-example-live-stream-on-twitch

xmas langmuir forum 2022 let it snow.dxf (606.6 KB)

xmas 20222 let it snow.nc (63.5 KB)
xmas langmuir forum 2022 let it snow.dxf (606.6 KB)

I’m really lukewarm on this design but I thought I wouldn’t let it go to waste and post it.

[TinWhisperer]

More pieces from above coming along.

My partner in this venture does the finishing mostly and he does a good job of it.

[TinWhisperer]

I’m going to be doing a rare evening live stream.

I’m batching it tonight.

Hoping to have a start time somewhere between 6:30 and 6:45 pm mst

I’ll split this up in to multi part. redoing the world compass bday gift

taking a break back at 8pm mst

[TinWhisperer]

Starting a live stream making the pattern to a sheet metal square to round.

545am mst

nice to see a couple people in the chat today! @KX9M included

You can away comment on the forum too if you dont have a twitch account.

here is an older topic i made about square to rounds

HVAC parts Square to Rounds 26 GA galvanized

I have made quite a few square to rounds over the years but this is the first using a CNC. Over the years I became very familiar with laying out and fabricating square to rounds by hand. When SketchUp came came out I started laying out fittings in that CAD environment , Acquiring all the true lengths, then stepping out the points with a compass on my sheet metal. Then I bought a bigger printer and could print out sometime 20 pieces of paper glue them down to the sheet metal, then cut out of t…

[KX9M]

Even though I’m not much of a sheet metal guy or Fusion guy… It’s that “Feed Your Head” thing that gets me… LOL

You never know what you might learn!! Thanks for the stream…

[TinWhisperer]

@KX9M

Here are the pictures.

If I was making more of them I would slightly adjust the measurements but turned out pretty good.

I would have won the race if I was laying it out and cutting it out by hand for a one off vs the CNC. Anything more than one it would have beat me.

20 gauge stainless 300 in per minute 25 amps fine cut consumables

[KX9M]

@TinWhisperer Not bad at all…!! Looks like it came out as planned…

Super good to spend a little time this morning…!!

[walton34]

Are these videos available anywhere else? Only a few of them are playing for me

[TinWhisperer]

@walton34 I have some available on YouTube.

They’re only available for 7 Days on twitch I do have them all saved my computer though.

The streams aren’t very polished so I usually only post them if someone requests a specific episode to get posted to YouTube.

TinWhisperer YouTube Is Now Up and Running

[tinwhisperer v1 youtube 16 9] Moved some content over to YouTube today from my twitch and loom pages. Check it out and please enjoy the videos If you have a specific video request please post below or send me a message. Or if there is a twitch video you want transferred to YouTube also let me know.

I’m getting ready to do another live stream this morning at about 4:00 -4:10a.m. mountain standard Time today.

[TinWhisperer]

stream today about this forum topic

Multiple segments into one

Im very new to fusion and the plasma table world. Ive got the XR and have cut some simple things and am ready to move on too more complex signs. My biggest problem is trying to select the contours in the manufacturing tab. Ive researched around and tried to find the “sketch check” add on but autodesk says it cannot find it. Does anyone have any ideas or better methods of fixing the multiple contour segments?

[KX9M]

Watched the stream but, wasn’t up in time for LIVE… LOL

So, it was a couple of broken corners and such… Nice work!!

[TinWhisperer]

Starting a live stream at 4 am mst

it on this topic

Torch stops at same spot every time

RX7 AIR PUMP tin forum .nc (1.6 KB) Air Pump Bracket 2 v10 tin forum v1.f3d (97.4 KB) [Air Pump Bracket 2 v10 tin forum v1] seems okay but a lot of lines of gcode to get the job done. Almost 600 lines . With fusions CAM try again and reduced it to 80 lines. your 1000mm per minute program speed or 40 inches be minute maybe to fast or slow for the material, what material are you using? Is the program trying to run at 1000 inch per minute? here is a live stream looking it over.

[LostWallet]

Please move to YouTube.

[TinWhisperer]

I just started an account 12 days ago

TinWhisperer YouTube Is Now Up and Running

[tinwhisperer v1 youtube 16 9] Moved some content over to YouTube today from my twitch and loom pages. Check it out and please enjoy the videos If you have a specific video request please post below or send me a message. Or if there is a twitch video you want transferred to YouTube also let me know.

I’m hoping to figure out how to tandem stream through my broadcasting software so I can stream both on YouTube and twitch at the same time.

If there’s any topic above that you’d like seen moved over to YouTube let me know I have them all saved to my computer.

I normally live stream quite early in the morning when I do live stream.

I was thinking about doing a scheduled live stream in the future about monograms.

[jamesdhatch]

@TinWhisperer

I’m hoping to figure out how to tandem stream through my broadcasting software so I can stream both on YouTube and twitch at the same time.

Are you using OBS?

[TinWhisperer]

@jamesdhatch

Are you using OBS?

Yes I’m using obs.

Apparently in August YouTube lifted the band on dual streaming from twitch…

[TinWhisperer]

Stream 5:45 am mst

Streaming Langmuir forum questions.

Talking about templating in Fusion 360 CAM

Topics Discussed

Tool library preset?

I still consider myself an amateur. Just implying that I don’t talk about it or cover it that much, 99% of what I do is basic workflow concepts. But it looks like it’s time to make a few intermediate videos. I’ll work through it on the live stream a few times and then put together a Polished video to post on YouTube. I talk about templating in fusion 360 cam. If @langmuir-aksel could please add the *.f3dhsm-template file extension to the “allowed” uploads the we can start experimenting…

and at 28 mintues

What is the best way to get details out of a file I purchased

What’s the best way to get the details out of a file I purchased. I’m trying to figure out how to get details out of a train file I purchased. I’m really am not trying to get everyone to do the work for me, as I’m trying to learn…and I’ve gotten a little better after watching @TinWhisperer but seems like the more detailed I get the harder it definitely gets…even tried scaling this file up bigger thinking it would help…but still losing lots of details. If it helps I’m using a Primeweld Cut60 with…

[TinWhisperer]

Beginning a live stream.

Twitch

Topics

-Group Editable flow charts for Forum troubleshooting Support.

-Forum Fusion 360 CAD Questions

https://lucid.app/lucidchart/adbad011-8893-4240-aa55-ec62d111762f/edit?viewport_loc=-181%2C-147%2C2219%2C1268%2C0_0&invitationId=inv_0ee266fc-26dc-402e-814f-e2efb59d491f

Here is a link to a document we can start trying this process on. I think this maybe very helpful for common forum issues

here is a example

6:30 am mst

[Knick]

I think that is a great idea.

@TinWhisperer

-Group Editable flow charts for Forum troubleshooting Support.

But how do you keep them from becoming out of control?
Seems like someone would need to be in control and at some point lock them so they cant be messed with?
Do you keep them to the basics and if it goes beyond that they would ask for help in the forum?

I really like the idea I’m just afraid they might get out of control or maybe they cant (I’m thinking forum threads)

So how would people find them? would there be a link in the forum?

[TinWhisperer]

Starting a live stream 9:25am mst

New 21:9 monitor!. Getting few file ready to cut today for stock.

New View !

21:9 center monitor. Getting few files ready to cut today for stock.

revamped my computer setup now I am thinking of cable management.