@KSiegel http://www.langmuirsystems.com/software/fusion#post-firecontrol
This guide will help you to install our FireControl post for Fusion360
3 Likes
Downloaded Firecontrol, looks good. Too bad we can’t simulate runs while we wait.
1 Like
wow… that took some tinkering…
think i got it… well see when everything is assembled and running.
i noticed the ZERO ALL AXES tab should probably be spelled AXIS right?
Nope. Axes is the plural of axis.
4 Likes
We would love for that to be possible in FireControl but unfortunately all of the motion control firmware is loaded onto the microprocessors on the board inside the electronics enclosure.
Oh well, guess I will have to be satisfied with toggling between inches and metric and back since that is the only function currently working on Firecontrol;-)
3 Likes
That’s funny right there!
Installed Firecontrol and installed post for sheetcam. I noticed in the note section of sheetcam post it states:
“For CrossFire PRO and CrossFire w/powered z-axis add-on, be sure to set Pierce Height, Plunge Rate, and Cut Height values in order to activate IHS sequence. There is a 1 inch rapid retract move after each cut loop by default.”
I have the Razorweld 45. Ive looked and cant find info for the pierce height. As far as cut height it would be .06 over material height correct? And what a good plunge rate? Sheetcam default is 3.937 IPM
You’ll notice that in our SheetCAM post guide (http://www.langmuirsystems.com/software/fusion#post-sheetcam) we recommend a 100IPM feed rate for the IHS plunge rate.
As for the razorweld 45A machines, we recommend using a pierce height of 0.150" and a cut height of 0.080".
4 Likes
I dont know how I missed this page!!! Thank you!
Hi Mike, Is the Firecam software still expected to be released mid summer- early fall? Havnt seen any mention of it latley.
1 Like
@jimt Our first priority right now is getting folks up and cutting with the new PRO machines but yes we are actively working on FireCAM. It’s hard to say when it will be released but we are making good progress on it!
4 Likes
Hey Mike, do you know when the boxes are leaving for us that got tracking last Friday? Tracking info still says “waiting for shipment”
@oneupperformance If you received a Box 2 tracking # Friday, you should see movement on it by this evening.
1 Like
Do send out tracking numbers on Friday for what is shipping the following week ?
If it’s like the original, they put lots of boxes on pallets that then get picked up by UPS. Since they’re all together, UPS gets a set of sheets with the tracking #s for everything on the pallet and they’re supposed to put those into their system. What we saw last time was that apparently, UPS didn’t do that until they broke a pallet apart when it arrived somewhere in the system where it couldn’t stay together. (For instance an East Coast pallet might get all the way to TN or GA before the individual boxes were pulled out to go to different states.)
There were folks close to LS that saw no progress until the day before it showed up 
Others of us further away got a couple or three days where it was finally on a locally bound truck so we could see it make its way to us.
1 Like
Not that I’m OCD or anything but I noticed if you have UPS MYchoice, you can look at the details on the “yet to progress” tracking number and it says “expected 2/27”…
…back to other OCD things.
Folks, they just created the shipping label this past friday.Sound that you guys are next in line for your boss 2. Perhaps if the hire couple of temps employees that could help expedite the process.
I think the saying goes “A watched pot never boils”…
I’m in batch #2 so my days of tracking number patrol are a ways out.
This forum is great, full of info, and is actually a nice coping method for all of us impatient overgrown kids that made the plunge…
2 Likes