well done…thanks
I made my own laptop stand (as a first CFP practice project) that required a longer usb cord. I’m running a 10’ long cord. Bought a 4 pack of ferrite chokes and have 2 on each end. Zero issues so far.
1 Like
Good read, I’m running a hynade plasma cutter since I’m using off brand and unknown compatibility I want to make sure I don’t introduce problems into my setup. Thank you.
Thank you.
https://www.amazon.ca/hynade-Voltage-cutting-Inverter-Thickness/dp/B08JV9YH92
Is this the plasma cutter you’re using?
What’s the exact model number of that machine?
It sure has the hallmarks of a high frequency machine which if it is you absolutely shouldn’t use it on your CNC machine.
But provide your model number and we could look it up more thoroughly, they make several different plasma cutters. I see some use blowback style consumables and some use high frequency style consumables.
The model I have is the Hynade CUT60DN definatly a blow back low frequency model.
2 Likes
After you have some run time on it please post your thoughts on the machine. I’ve been thinking about picking up their CUT80 machine as a dedicated cutter just for the CFP.
Somewhere langmuir states that their machines are designed for 40-50amp plasma cutters. I am unaware if going above that effects something. But it’s good for thought.
I think what you are referring to is that they say the water table is designed to work with plasma cutters running 45 amps or less.
@Bigdaddy2166 can testify to that… 
They say if you are using more than 45 amps you should consider providing a plate liner on the bottom of the table.
2 Likes
That’s what I do. Have an old skanky piece of stainless plate I put in the pan when cutting the thick stuff at high amps. Have cut 3/4" and 1" without any issues.
2 Likes
I have used a 15’ long cable from my desktop to do test runs on my legacy crosscut machine. I have it outside under my back porch and view it with an overhead mounted Ring camera during the practice runs. I get a lot of sun out there so only take my laptop out to run and cut when it’s cooler. I added two Ferrite beads to each end of the long cable. No problems on No plasma only dry runs. Shorter different cable, also with ferrite beads, during cutting.
1 Like
Good to know thanks.
USB A has a spec limit of about 10’ You can swing 15’ out of it if there’s not a lot of ambient electrical noise (not near a plasma cutter or welder). If you need to go further you can get USB over Ethernet adapters for less than $20 on Amazon (use a brand name… The Monoprice ones are fine) this will get you 100ft or so. Use a good quality Cat 6 or cat7 shielded network cable and try to run it as far from the table and Plasma cutter cables as possible. We use these adapters all over at the schools I work at (75-100 classrooms) with good results. I’ve not tried one in my Shop because my laptop is close. I’m moving to a new shop (yet to be built) so all my stuff’s in storage or I’d put one on and test it for you.
Good Luck!
(I’ve added links to the items I talked about. I get no kickback from the links and I don’t work for Amazon or the other companies. I’m just doing it to make it easy to find.)
1 Like
I’m got a 30 foot cable from Amazon and no problems.
Anyone have any luck with Maono printer Cables? Was looking to purchase a longer cable as well and ran across Maono brand, only one ground band on it.
https://www.amazon.com/MAONO-Maono-USB-Printer-Cable/dp/B09L4RYTDG
Is this the style of cable you’re talking about in the link above?
If I was buying an aftermarket cable I’d be tempted to get the type that has the two ferrite chokes, one at each end. Like in this picture.
3 Likes
wow. here is a low noise 10’ er for only 900$us.
those audiophiles are something else…
Holy smokes, I’m looking for something a little cheaper 
2 Likes