This first program has a 5/8" hole with no feed rate optimizer added
(v1.6-af)
G90 G94
G17
G20
H0
(2D Profile1)
G0 X0.5694 Y0.5146
G92 Z0.
G38.2 Z-5. F100.
G38.4 Z0.5 F20.
G92 Z0.
G0 Z0.04 (IHS Springback + Backlash)
G92 Z0.
G0 Z0.15 (Pierce Height)
M3
G4 P0.7
G0 Z0.06 (Cut Height)
H1
G3 X0.841 Y0.5625 I0.1316 J0.0479 F90.
G3 X0.284 I-0.2785 J0. F90.
G3 X0.5825 Y0.2847 I0.2785 J0.
G3 X0.8381 Y0.6024 I-0.02 J0.2778
H0
M5
G0 Z1.
M30
(PS90)
Program speed
This second has a 5/8" hole with feed rate optimizer added so there is more optimized length then standard length of cut
(v1.6-af)
G90 G94
G17
G20
H0
(2D Profile1)
G0 X0.5694 Y0.5146
G92 Z0.
G38.2 Z-5. F100.
G38.4 Z0.5 F20.
G92 Z0.
G0 Z0.04 (IHS Springback + Backlash)
G92 Z0.
G0 Z0.15 (Pierce Height)
M3
G4 P0.7
G0 Z0.06 (Cut Height)
H1
G3 X0.841 Y0.5625 I0.1316 J0.0479 F90.
G3 X0.284 I-0.2785 J0. F54.
G3 X0.5825 Y0.2847 I0.2785 J0.
G3 X0.8381 Y0.6024 I-0.02 J0.2778
H0
M5
G0 Z1.
M30
(PS0)
no program speed
now here is a hole in a square with feed rate optimized applied so there is more length of non optimized cutting then optimized
(v1.6-af)
G90 G94
G17
G20
H0
(2D Profile1)
G0 X0.7445 Y0.7979
G92 Z0.
G38.2 Z-5. F100.
G38.4 Z0.5 F20.
G92 Z0.
G0 Z0.04 (IHS Springback + Backlash)
G92 Z0.
G0 Z0.15 (Pierce Height)
M3
G4 P0.7
G0 Z0.06 (Cut Height)
H1
G3 X0.4729 Y0.75 I-0.1316 J-0.0479 F90.
G3 X1.0299 I0.2785 J0. F54.
G3 X0.7314 Y1.0278 I-0.2785 J0.
G3 X0.4758 Y0.7101 I0.02 J-0.2778
H0
M5
G0 Z1.
G0 X-0.0555 Y0.7021
G92 Z0.
G38.2 Z-5. F100.
G38.4 Z0.5 F20.
G92 Z0.
G0 Z0.04 (IHS Springback + Backlash)
G92 Z0.
G0 Z0.15 (Pierce Height)
M3
G4 P0.7
G0 Z0.06 (Cut Height)
H1
G3 X0.216 Y0.75 I0.1316 J0.0479 F90.
G1 Y0.91
G1 Y1.25 F54.
G2 X0.25 Y1.284 I0.034 J0.
G1 X0.9128 F90.
G1 X1.2528 F54.
G2 X1.2868 Y1.25 I0. J-0.034
G1 Y0.59 F90.
G1 Y0.25 F54.
G2 X1.2528 Y0.216 I-0.034 J0.
G1 X0.59 F90.
G1 X0.25 F54.
G2 X0.216 Y0.25 I0. J0.034
G1 Y0.75 F90.
G1 Y0.79
H0
M5
G0 Z1.
M30
(PS90)
program speed
works again.